Special Finishes

Architectural and Decorative Coating Specialists

Colourtrend Acrylic PaintsColourtrend Acrylic Paints

Ultracoat 100

Print this page Save this page as a PDF Product enquiry

Description:

Ultracoat 100 is a two pack aliphatic reactive urethane for exterior/interior coloured coatings designed where excellent chemical resistance, moisture abrasion and resistance against petroleum solvents, oils, alkalies, acids, etc. is required.  Coloured films have high quantities of ultra-violet protective additives and are tough, resilient and non-yellowing with exceptional exterior durability.

Uses:

Ultracoat 100 system provides a very hard durable finish with high resistance to a wide range of chemicals and are particularly suited to coat over machines, petrochemical plants, electro power plants, oil refineries, steel, equipment, automotive, food processing areas, freezing works, meat and dairy industries, hospitals, building complexes, industrial complexes, Aquepoxy floors, Flooring, interior or exterior, coloured coating over Hi Build Acrylic Systems, Anti-Graffiti Coating over blocks, buildings and walls, for long lasting finish on boats, flooring etc.

Substrate Temperatures:

Do not apply below 10'C.  At this temperature cure rate will be considerably reduced.

Not Recommended:

Application to damp surfaces.  Immersion in Acids, Alkalies or Solvents.

Handling Precautions:

Solvent and resin fumes can be harmful and can contaminate foodstuffs.  Provide and wear suitable respirator and protective clothing when spraying.

Warning:

Provide adequate ventilation at all times.  Contains Isocyanate - A complete air assisted breathing apparatus to be used when spraying.

Flash point:

24'C contents flammable.

N.Z. Dangerous goods Class:

3B, UN NO.: 1263

Mixing Ratio:

By volume - Mix 50 / 50 equal parts Part A to Part B

Small quantity:

Mix equal parts Part A to Part B (200mls of each) Important to keep correct accurate mixing ratio by volume to ensure proper curing and hardness.

Application for Spraying:

  1. Mix ultracoat 100 equal parts by volume.
  2. Allow to stand for 5 minutes induction time.
  3. Add 60-100% U.C. 500 reducer, thoroughly mix together.
  4. Apply 1 even light coat, allow ultracoat 100 to tack off for 10-20 minutes before futher application.
  5. Then apply further coats utilising this same technique to obtain desired finish.

Warning:

Application of a thick filmbuild with coat after coat in quick succession can entrap solvent that would result in a softer film when cured.

Minimum Application Temperature:

10'C

Increase Cure:

In cold conditions addition of Activator Quickset will speed up cure times, 1-2 hours.

Pot Life:

25'C 50% relative humidity - 2 hours.

Dry Time:

25'C 50% relative humidity

Recoat: 20 Minutes-16 hours. maximum 16 hours
Surface Dry: 4 Hours
Hard Dry: 12 Hours

 

Coverage Rate:

Steel / Machinery / Automotive / Industrial: 12-20 m2 per litre
Walls: 8-12 m2 per litre
Floors: 4 m2 per litre (3 coats minimum)

Film Build:

Wet:

Walls

Floors / Plant / Machinery / Automotive

125 microns (0.005) per coat

250 microns (0.010) per coat

Dry:

Walls

Floors / Plant / Machinery / Automotive

50 microns (0.002) per coat

100 microns (0.004) per coat

Warranty / Liability

Special Finishes (NZ) Ltd provides all the enclosed information in good faith but without warrantee and is to assist your application. However the use of this product being used is beyond their control. The manufacturers can accept no responsibility whatsoever for any damage or failure arising from its application or use. It is totally the responsibility of the user to insure that the product is suitable for its intended use.