A premium quality Alkyd Resin High Gloss paint that is ideal for
interior or exterior where a durable finish is demanded. Can
be tinted to any of the BS 5252 colours.
Weatherboard houses or wooden trim - on any type of
construction,eaves, facias and gable ends. Ideal interior,
where a top grade finish is to be specified - bathrooms, kitchens,
ablution areas and on trim such as scotia, architraves and
skirtings.
Enamel High Gloss should be applied over Special Finishes' high
opacity Multiseal Alkyd Undercoat which has had a minimum of
12 hours to dry.
Timber interior - apply 2 coats of Multiseal Alkyd Undercoat,
leaving a minimum of 12 hours between coats following normal
procedures for filling nail holes, cracks etc. When dry,
lightly sand - then apply 1 or 2 coats of Special Finishes' premium
Enamel High Gloss to desired colour, leaving a minimum of 12 hours
drying between coats.
| Coverage: |
8 - 10 m² per litre |
| Applied by: |
Brush, roller or spray |
| Thinning & Clean up: |
Mineral Turpentine |
| Drying Time: |
6 - 8 hours (leave 12 hours between coats) |
An Alkyd resin undercoat possessing outstanding obliteration and
holdout properties, free sanding, minimal brush drag - can be
tinted to a lightened version of eventual colour, if desired.
| Coverage: |
7 - 8 m² per litre |
| Applied by: |
Brush, roller or spray |
| Thinning & Clean up: |
Mineral Turpentine |
| Drying Time: |
6 - 8 hours (depending on drying conditions - should be left 12
hours minimum between coats) |
A premium matt finish, particularly suited to ceilings where a
velvet smooth quality finish is to be specified. In most
cases 2 coats direct on to new plaster or gib-board ceilings is all
that is required. However, some staining may eventually occur
on old or sun-browned gib-board and on plaster to which Contractors
have added Retarding Agents such as Casein Products. If in
doubt a pre-coat of Multiseal Alkyd Sealer is advised.
| Coverage: |
10 -12 m² per litre |
| Applied by: |
Brush, roller or spray |
| Thinning & Clean up: |
Mineral Turpentine |
| Drying Time: |
6 - 8 hours (leave 12 hours between coats) |
Especially formulated to be compatible with all Special
Finishes' products. Recommended under alkyd finishes as
above, or under Acrylic finishes such as Sprayflex (see separate
data sheet).
| Coverage: |
8 - 12m² per litre |
| Applied by: |
Brush or roller |
| Thinning & Clean up: |
Mineral Turpentine |
| Drying Time: |
6 - 8 hours |
A clear non-yellowing single pack abrasion resistant modified
Alkyd resin, that is flexible and moderately heat resistant,
allowing a wide ranging use from floors to table tops. A
minimum 3 coat recommendation on most surfaces such as timber, chip
board, cane, etc., but areas such as flooring grade particle board
and cork may require up to 5 coats to achieve the desired
finish. Always lightly scuff between coats.
Polyurethane is not recommended on vinyl or linoleum. the
first coat on most surfaces is usually thinned up to 15% with Turps
to aid penetration and achieve an even sealing coat.
| Coverage: |
10 - 12 m² per litre |
| Applied by: |
Brush, roller or spray |
| Thinning & Clean Up: |
Mineral Turpentine |
| Drying Time: |
6 - 8 hours (12 hours between coats) |
Warranty / Liability
Special Finishes (NZ) Ltd provides all the enclosed information in good faith but without warrantee and is to assist your application. However the use of this product being used is beyond their control. The manufacturers can accept no responsibility whatsoever for any damage or failure arising from its application or use. It is totally the responsibility of the user to insure that the product is suitable for its intended use.