Special Finishes

Architectural and Decorative Coating Specialists

Colourtrend Acrylic PaintsColourtrend Acrylic Paints

Exterior Wall Coating System

Print this page Save this page as a PDF Product enquiry


Multifleck Exterior has been specifically formulated for exterior application based on a proven Pure Acrylic System that has exceptional exterior durability blended with sophisticated ultra-violet light protective properties, incorporating biocides, mould, mildew and algae inhibitors to give extensive long term protection.  Used etensively on large commercial building complexes, etc.

Typical Properties:

Etremely fleible - displays excellent early blanch, water, alkali, oil and grease resistant characteristics.


Internally plasticised, cross linking membrane system, remains permanently flexible.

  • Long term protection from mould or algae
  • Excellent weathering properties
  • Completely new designer colours to simulate granite or metallic look
  • Appearance of granite or marble at lower cost
  • Designed for long term protection in tropical countries

Application Existing Buildings or New Buildings

Preparation Existing Buildings:

Apply 1 coat of Chemocide and completely waterblast total area using minimum of 3000 PSI unit, ensuring all mould, grease, grime, loose or flaky paint is compleely removed.  Allow to dry.  Repair any defects in concrete using Shieldpatch Acrylic Modified Cement mixed with Resin 50.

Preparation New Buildings:

Ensure building is clean and dust free. Repair any defects in concrete using Epoxyflex or Shieldpatch Acrylic Modified Cement mixed with Resin 50.  Allow to dry.  Do not use ordinary sand and cement, as loss of adhesion may occur.


Apply 1 coat of Strongwall Sealer using roller or spray to ensure proper adhesion to concrete and exxisting paint systems.


Apply 1 coat of Basecolour using roller, airless spray, or pressure pot spray system at 5m2 er litre coverage.  On concrete allow 2 coats at 5m2 per litre coverage on blockwork.

Multifleck Application:

Apply 1 coat of Multifleck at 3m2 per litre coverage to achieve a minimum film build of 333 microns W.F.B.

Even though we use the same base colour, it is very important to completely overlap and interknit each spray pass of Multifleck at 50% completely obliterating the basecolour.  It is important that basecolour does not grin through.

Allow minimum of 8 -16 hours to dy before rain and overglazing.

Glaze Coat:

Apply 2 even coats of Crystal Glaze at 6m2 per litre coverage (allow to dry before heavy rainfall) for additional protection and improved performance especially in harsh weather environments.

Multifleck Application:

Apply Multifleck overlapping each spray pass by 50% holding spray gun 200-300 mm from surface and directly at surface (not angling, otherwise damage will result)

Continue this technique ensuring all Basecolour is completely obliterated (Basecolour or Multiseal should not grin through).

Continue fnishing with this technique completing the area as you go, this system requires only 1 coat.

Spray all angles, edges, and intricate tricky areas first, only then proceed to spray large flat areas maintaining Spray Gun directly at approximately 10-15 inches (200-300 mm) away from substrate for best results.

Glaze Coat:

Apply 2 even coats of Crystal Glaze at 6m2 per litre coverage (allow to dry before heavy rainfall) for additional protection and improved performance especially in harsh weather environments.  Multifleck Will Not spray through Suction Cup Guns or Airless Spray Pumps as too higher pressures will shatter the flecks

Warranty / Liability

Special Finishes (NZ) Ltd provides all the enclosed information in good faith but without warrantee and is to assist your application. However the use of this product being used is beyond their control. The manufacturers can accept no responsibility whatsoever for any damage or failure arising from its application or use. It is totally the responsibility of the user to insure that the product is suitable for its intended use.